RedHat6.5网卡问题总结

问题描述:准备用RedHat6.5安装Oracle 12c RAC,系统环境准备好后发现,新版本的RedHat网卡配置跟以前不大一样,总结问题与解决方法如下:

1、找不到eth0文件

在使用RedHat6.5,新装好的系统,发现没有eth0网卡,默认的第一个网卡是Auto-eth0

[root@rac01 ~]# cat /etc/sysconfig/network-scripts/ifcfg-Auto_eth0

TYPE=Ethernet

BOOTPROTO=none

IPADDR=10.10.10.110

PREFIX=24

GATEWAY=10.10.10.111

DEFROUTE=yes

IPV4_FAILURE_FATAL=yes

IPV6INIT=no

NAME=eth0

UUID=86d44060-4579-48cc-b85b-219a206ca37c

ONBOOT=yes

HWADDR=00:50:56:95:09:76

LAST_CONNECT=1411004329

解决方法:

直接更名ifcfg-Auto_eth0文件为eth0,重启网卡后会发现,网卡名已经变为eth0

[root@rac01 ~]# service network restart

Bringing up loopback interface:                            [  OK  ]

Bringing up interface eth0:  Active connection state: activated

2、ifconfig 发现网卡服务名并未更改

[root@rac01 ~]# ifconfig

Auto_eth0 Link encap:Ethernet  HWaddr 00:50:56:95:09:76 

inet addr:10.10.10.110  Bcast:10.10.10.111 Mask:255.255.255.0

inet6 addr: fe80::250:56ff:fe95:976/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:484 errors:0 dropped:0 overruns:0 frame:0

TX packets:57 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:40095 (39.1 KiB)  TX bytes:6271 (6.1 KiB)

解决方法:

每次更改RedHat的网卡信息,RedHat会自动的将网卡的MAC地址和对应的网卡服务名关系记录在/etc/udev/rules.d/70-persistent-net.rules中,修改里面的对应服务名即可

[root@rac01 ~]# vim /etc/udev/rules.d/70-persistent-net.rules

# This file was automatically generated by the /lib/udev/write_net_rules

# program, run by the persistent-net-generator.rules rules file.

#

# You can modify it, as long as you keep each rule on a single

# line, and change only the value of the NAME= key.

# PCI device 0x15ad:0x07b0 (vmxnet3)

SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0c:29:1e:f6:ad", ATTR{type}=="1", KERNEL=="eth*",

修改完成后需重启一下系统,再次查看网卡服务名已经更改

[root@rac01 ~]# ifconfig

eth0      Link encap:Ethernet  HWaddr 00:50:56:95:09:76 

inet addr:10.109.67.81  Bcast:10.109.67.255  Mask:255.255.255.0

inet6 addr: fe80::250:56ff:fe95:976/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:985 errors:0 dropped:0 overruns:0 frame:0

TX packets:61 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:74395 (72.6 KiB)  TX bytes:6527 (6.3 KiB)

3、网卡eth0被删除后,新加的网卡成了eth1,如何让从eth0开始
 

[root@rac01 ~]# ifconfig

eth1      Link encap:Ethernet  HWaddr 00:50:56:95:09:76 

inet addr:10.10.10.110 Bcast:10.10.10.111  Mask:255.255.255.0

inet6 addr: fe80::250:56ff:fe95:976/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:830 errors:0 dropped:0 overruns:0 frame:0

TX packets:57 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:63700 (62.2 KiB)  TX bytes:6259 (6.1 KiB)

eth2      Link encap:Ethernet  HWaddr 00:0C:29:1E:F6:B7 

inet addr:10.10.10.120  Bcast:10.10.10.111Mask:255.255.255.0

inet6 addr: fe80::20c:29ff:fe1e:f6b7/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:777 errors:0 dropped:0 overruns:0 frame:0

TX packets:11 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:54938 (53.6 KiB)  TX bytes:746 (746.0 b)

解决方法:

同2问题类似,即可以手动的修改70-persistent-net.rules文件,将对应的MAC地址与网卡序号改成想要的,也可以直接删除该文件,重启系统后,RedHat会自动的创建该文件,并从0开始计数。

删除文件,重启系统

[root@rac01 ~]# mv /etc/udev/rules.d/70-persistent-net.rules /etc/udev/rules.d/7

0-persistent-net.rules.bak

[root@rac01 ~]# reboot

再次查看,会发现已经从eht0开始

[root@rac01 ~]# ifconfig

eth0      Link encap:Ethernet  HWaddr 00:50:56:95:09:76 

inet addr:10.109.67.81  Bcast:10.109.67.255  Mask:255.255.255.0

inet6 addr: fe80::250:56ff:fe95:976/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:206 errors:0 dropped:0 overruns:0 frame:0

TX packets:68 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:19282 (18.8 KiB)  TX bytes:7215 (7.0 KiB)

eth1      Link encap:Ethernet  HWaddr 00:0C:29:1E:F6:B7 

inet addr:10.109.67.83  Bcast:10.109.67.255  Mask:255.255.255.0

inet6 addr: fe80::20c:29ff:fe1e:f6b7/64 Scope:Link

UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

RX packets:131 errors:0 dropped:0 overruns:0 frame:0

TX packets:11 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000 

RX bytes:8736 (8.5 KiB)  TX bytes:746 (746.0 b)

4、每次重启网卡,总是提示

Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/9

此时网卡也可以正常通信,这个是因为RedHat自己开发的NetworkManager管理工具和/etc/sysconfig/network-scripts/ifcfg-ethx配置不同步造成的。

解决方法:

要消除这个提示,请关闭NetworkManager服务即可:

[root@rac01 ~]# service network restart

Shutting down loopback interface:                        [  OK  ]

Bringing up loopback interface:                            [  OK  ]

Bringing up interface eth0:  Active connection state: activated

Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/2  [  OK  ]

Bringing up interface eth1:  Active connection state: activated

Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/3  [  OK  ]

关闭NetworkManager服务

[root@rac01 ~]# service NetworkManager stop

Stopping NetworkManager daemon:                            [  OK  ]

再次重启网卡

[root@rac01 ~]# service network restart

Shutting down loopback interface:                    [  OK  ]

Bringing up loopback interface:                          [  OK  ]

Bringing up interface eth0:                                [  OK  ]

Bringing up interface eth1:                                [  OK  ]

内容版权声明:除非注明,否则皆为本站原创文章。

转载注明出处:http://www.heiqu.com/17222.html